Your SAFTI-TRAX MAT™ Detectable Warning System is now complete!ĬAUTION: Do not apply when moisture-vapor transmission condition exists from the substrate, as this can cause bubbling within the sealant. Let adhesive dry for at least 6 hours before allowing foot traffic. (SAFTI-TRAX MATS™ are precoated with COTE-L’s DURABAK 18™ moisture-cured polyurethane coating.)ġ3. If need be, DURABAK™ can later be used for touch-up with a small brush.
Remove any excess adhesive with a rag that has been dampened with xylene. Work inbetween the domes, from the center out, paying particular attention to pressing down all areas around the outside perimeter.ġ2. Use the end of the board or another board to press down all areas in between the domes. Move the board around making sure that all areas of each mat have been pressed down. Lay a small, flat board (1 square foot or smaller) on the top of the domes and press down firmly. WITH YOUR HANDS, PRESS OUT ANY AIR POCKETS FROM THE CENTER OF THE MAT OUTWARDS TO THE EDGES.ġ1. Carefully place the mats back in their original position on the surface, making sure that they are not overlapping the duct tape.ġ0. A 1-1/4 tube covers 4 square feet.įAILURE TO COVER ENTIRE AREA UNDER THE MAT WILL RESULT IN AIR SPACES AND POSSIBLE BLISTERING WHICH MIGHT INTERFERE WITH A COMPLETE BOND WITH THE SUBSTRATE.ĩ. Using a serrated trowel, spread the adhesive to cover the entire masked-off surface (paying particular attention to making sure that the perimeter of the area is covered right up to the duck-taped edges). Squeeze out a large bead of adhesive over one half the surface.Ĩ. Place the adhesive in the caulk gun, cut of 1/4″ to 1/2″ of the tube’s plastic tip, and pierce the inner seal of the caulk tube.ħ. Remove the mat(s) from the working area, remembering the exact position they were in.Ħ. Mask off the area around the mat(s) with a good-quality duct tape, which bonds to the concrete better than regular masking tape.ĥ. Place mat(s) onto the application surface.Ĥ. Agitate with a deck brush, rinse off thoroughly and dry completely.ģ. Alternatively, new concrete will require only a citric cleaner application. If there is gum or other contaminants on the surface, remove with a clean wire brush. Clean the surface using a pressure wash of at least 2500 psi. (If necessary, bend them to make them lie flat.)Ģ. Lay mat(s) flat away from the actual final placement. Clean the SAFTI-TRAX MAT(s) with rubbing alcohol and let dry. Please read all instructions carefully before proceeding.ġ. Cutting fees will apply.Safti-Trax Mat™ Detectable Warning System Installation Installation Instructions
#Clean trax mat full
For pricing will be rounded to next full standard width. ** Custom widths available in full inches only. For pricing will be rounded to next full foot. * Custom lengths available in full inch increments only.
#Clean trax mat code
Vinyl top surface bonded to a dense sponge base - enhances ergonomic benefit and worker comfort.Īvailable with 4" colored borders - borders comply with OSHA code #1910-144 For ultimate anti-fatigue relief see our item S002-979 (essentially the same item just full 1 inch thick). UniFusion™ bond guaranteed for the life of the mat. Tip - for applications on carpeted, finished or polished surfaces MATHOLD is recommended to minimize mat movement.Īleviates foot pressure, stimulates blood circulation and helps reduce stress on the lower back, leg joints and major muscle groups. Suggested Uses - Machine operating stations needing fatigue prevention and sure footing. RedStop™ provides increased friction between the underside of the mat and a clean, dry floor surface anchoring the mat in place, without leaving a tacky or sticky residue.ĭistinctive Feature - diamond surface provides non-directional slip resistance. NoTrax® floor mats with RedStop™ are targeted for use in environments where smooth floor surfaces are found such as vinyl composite tile, painted or epoxy coated concrete, vinyl sheet flooring, carpet, and ceramic tile.
Now featuring RedStop Anti-Slip technology. The diamond deck plate vinyl top surtace provides non-directional traction and is easy to clean. Designed for ultimate comfort and worker support in the harshest dry environments like assembly lines, lab areas, machinist workstations, and packaging stations.
0 kommentar(er)
